Configuration Options for 18F97J60

Background Debugger:
	DEBUG = ON		Enabled
	DEBUG = OFF		Disabled

Extended Instruction Set:
	XINST = OFF		Disabled
	XINST = ON		Eanbled

Stack Overflow/Underflow Reset:
	STVREN = OFF		Reset disabled
	STVREN = ON		Reset enabled

Watchdog Timer Enable:
	WDTEN = OFF		WDT disabled
	WDTEN = ON		WDT enabled

Code Protection:
	CP0 = ON		code protected
	CP0 = OFF		not code protected

Two Speed Start Up:
	IESO = OFF		Disabled
	IESO = On		Enabled

Fail Safe Clock Monitor:
	FCMEN = OFF		Disabled
	FCMEN = ON		Enabled

Default Reset System Clock:
	FOSC2 = OFF		INTRC enabled as system clock when OSCCON 1:0 = 00
	FOSC2 = ON		Clock selected by FOSC1:FOSC0 when OSCCON 1:0 = 00

Oscillator Selection:
	FOSC = HS		HS oscillator
	FOSC = HSPLL		HS with PLL
	FOSC = EC		EC oscillator with CLKOUT on RA6
	FOSC = ECPLL		EC oscillator with PLL

Watchdog Timer Postscaler:
	WDTPS = 1		1:1
	WDTPS = 2		1:2
	WDTPS = 4		1:4
	WDTPS = 8		1:8
	WDTPS = 16		1:16
	WDTPS = 32		1:32
	WDTPS = 64		1:64
	WDTPS = 128		1:128
	WDTPS = 256		1:256
	WDTPS = 512		1:512
	WDTPS = 1024		1:1024
	WDTPS = 2048		1:2048
	WDTPS = 4096		1:4096
	WDTPS = 8192		1:8192
	WDTPS = 16384		1:16384
	WDTPS = 32768		1:32768

External Bus Wait:
	WAIT = ON 		Wait states for operations on external memory bus enabled and selected by MEMCON<5:4>
	WAIT = OFF 		Wait states for operations on external memory bus disabled

Data Bus Width Select bit:
	BW = 8 			8-Bit Data Width mode
	BW = 16 		16-Bit Data Width mode

External Memory Bus Configuration bits:
	MODE = XM20 		Extended Microcontroller mode, 20-Bit Address mode
	MODE = XM16 		Extended Microcontroller mode,16-Bit Address mode
	MODE = XM12 		Extended Microcontroller mode,12-Bit Address mode
	MODE = MM 		Microcontroller mode, external bus disabled

External Address Bus Shift Enable bit:
	EASHFT = OFF 		Address shifting disabled; address on external bus reflects the PC value
	EASHFT = ON 		Address shifting enabled; address on external bus is offset to start at 000000h

Ethernet LED Enable bit:
	ETHLED = OFF 		RA0/RA1 function as I/O regardless of Ethernet module status
	ETHLED = ON 		RA0/RA1 are multiplexed with LEDA/LEDB when Ethernet module is enabled and function as I/O when Ethernet is disabled

ECCP MUX bit:
	ECCPMX = OFF 		ECCP1 outputs (P1B/P1C) are multiplexed with RH7 and RH6; ECCP3 outputs (P3B/P3C) are multiplexed with RH5 and RH4
	ECCPMX = ON 		ECCP1 outputs (P1B/P1C) are multiplexed with RE6 and RE5; ECCP3 outputs (P3B/P3C) are multiplexed with RE4 and RE3

ECCP2 MUX bit:
	CCP2MX = OFF 		ECCP2/P2A is multiplexed with RE7 in Microcontroller mode (80-pin and 100-pin devices) or with RB3 in Extended Microcontroller mode (100-pin devices only)
	CCP2MX = ON 		ECCP2/P2A is multiplexed with RC1