Configuration Options for 18F1320

   Oscillator Selection:
     OSC = LP             LP Oscillator
     OSC = XT             XT Oscillator
     OSC = HS             HS Oscillator
     OSC = EC             External Clock on OSC1, OSC2 as Fosc/4
     OSC = ECIO           External Clock on OSC1, OSC2 as RA6
     OSC = HSPLL          HS + PLL
     OSC = RCIO           External RC on OSC1, OSC2 as RA6
     OSC = INTIO2         Internal RC, OSC1 as RA7, OSC2 as RA6
     OSC = INTIO1         Internal RC, OSC1 as RA7, OSC2 as Fosc/4
     OSC = RC             External RC on OSC1, OSC2 as Fosc/4

   Fail Safe Clock Monitor:
     FSCM = OFF           Fail Safe Clock Monitor disabled
     FSCM = ON            Fail Safe Clock Monitor enabled

   Internal External Switch Over mode:
     IESO = OFF           Internal External Switch Over mode disabled
     IESO = ON            Internal External Switch Over mode enabled

   Power-Up Timer:
     PWRT = ON            Enabled
     PWRT = OFF           Disabled

   Brown-Out Reset:
     BOR = OFF            Disabled
     BOR = ON             Enabled

   Brown Out Voltage:
     BORV = 45            4.5V
     BORV = 42            4.2V
     BORV = 27            2.7V
     BORV = 20            2.0V

   Watchdog Timer:
     WDT = OFF            Disabled
     WDT = ON             Enabled

   Watchdog Postscaler:
     WDTPS = 1            1:1
     WDTPS = 2            1:2
     WDTPS = 4            1:4
     WDTPS = 8            1:8
     WDTPS = 16           1:16
     WDTPS = 32           1:32
     WDTPS = 64           1:64
     WDTPS = 128          1:128
     WDTPS = 256          1:256
     WDTPS = 512          1:512
     WDTPS = 1024         1:1024
     WDTPS = 2048         1:2048
     WDTPS = 4096         1:4096
     WDTPS = 8192         1:8192
     WDTPS = 16384        1:16384
     WDTPS = 32768        1:32768

   MCLR Enable:
     MCLRE = OFF          Disabled
     MCLRE = ON           Enabled

   Stack Full/Overflow Reset:
     STVR = OFF           Disabled
     STVR = ON            Enabled

   Low Voltage ICSP:
     LVP = OFF            Disabled
     LVP = ON             Enabled

   Background Debugger Enable:
     DEBUG = ON           Enabled
     DEBUG = OFF          Disabled

   Code Protection Block 0:
     CP0 = ON             Enabled
     CP0 = OFF            Disabled

   Code Protection Block 1:
     CP1 = ON             Enabled
     CP1 = OFF            Disabled

   Boot Block Code Protection:
     CPB = ON             Enabled
     CPB = OFF            Disabled

   Data EEPROM Code Protection:
     CPD = ON             Enabled
     CPD = OFF            Disabled

   Write Protection Block 0:
     WRT0 = ON            Enabled
     WRT0 = OFF           Disabled

   Write Protection Block 1:
     WRT1 = ON            Enabled
     WRT1 = OFF           Disabled

   Boot Block Write Protection:
     WRTB = ON            Enabled
     WRTB = OFF           Disabled

   Configuration Register Write Protection:
     WRTC = ON            Enabled
     WRTC = OFF           Disabled

   Data EEPROM Write Protection:
     WRTD = ON            Enabled
     WRTD = OFF           Disabled

   Table Read Protection Block 0:
     EBTR0 = ON           Enabled
     EBTR0 = OFF          Disabled

   Table Read Protection Block 1:
     EBTR1 = ON           Enabled
     EBTR1 = OFF          Disabled

   Boot Block Table Read Protection:
     EBTRB = ON           Enabled
     EBTRB = OFF          Disabled